Infrared Sensor

Sensors are everywhere, some examples:

* Smaller shops or barbershops, often have a beam of light crossing the room near the door, which ends up in a photo-sensor on the other side of the room. When a customer breaks that beam, the bell rings.

* Bigger markets have automated doors, the black bulb above the door sends a burst of microwave radio energy, and waits for the reflected energy to bounce back. When a person walks into that field, the amount of energy is changed,...resulting in the door to open. Therefor you can't just run in a market, the doors wont open fast enough ;). So no kidz, it doesn't have a little leprecon in it, which presses a button to open the doors!!


* Same thing with ultrasonic sound waves used by bats for example, they bounce back off a target and create an image.
These are what we call active sensors. They send out energy, and detect changes in them .


Motion Sensor

The motion sensing system is a passive sensor. It detects infrared energy. Human beings have a skin temperature of approximately 36° Celsius or 93° Fahrenheit, this produces an infrared energy with a wavelength between 9 and 10 micrometers. When infrared energy is detected, that infrared light bumps electrons of the sensors substrate, these are amplified and result in a signal.
People who have these little sensors, may notice that the sensing light doesn't go off when you're standing still. That's because the sensor is programmed to sense rapidly changes, you don't want every change of infrared light setting off the alarm .

If you're searching for a hack in this system, ...than this is your lucky day, because you can. The sensors are sensitive in a range of 8 - 12 micrometers. So all you need to do is calculate what body temperature you got to have to produce waves of 7 micrometers or less. I'm not responsible if you got hypothermia afterwards ;) . Or maybe you could build a glass bulb around you, glass doesn't let the infrared waves through, think of a greenhouse, the light goes in , but then it's trapped inside... so beware of people passing by in the possession of glass bulbs...

Footnote: During Operation: Desert Storm. The US military used infrared vision equipped tanks to spot and fight hostile tanks at night. Result: hostile tanks getting slaughtered like a sitting duck, technology = win
About the Author:

I'm Jan Vansteenlandt, i'm 19 years old, i still attend school.

My articles will be around the technology topic, and all it's subcategories. Normally IT-related.

I hope you enjoy them :)

Article Source: http://www.articlesbase.com/electronics-articles/infrared-sensor-544013.html

Read More......

Speed Sensors of Turbine

With turbine technology finding its way into more and more aspects of todays high tech world, many people just like yourself may find themselves in uncharted water in having to deal with them. The fact is, that turbines can be simple or extremely complex depending on what they are used in.

A Complex Turbine

For instance, a modern jet will have a highly complex turbine engine that burns fuel inside a series of alloy fan bladed to generate thrust. This would be a highly complex example of a turbine system being used to generate kinetic energy and force.

A Simple Turbine Engine

At the same time, the simple spinning vent on the roof of a house is yet another example of a far more simpler turbine engine. Even though it has only one moving part, it is by definition, a turbine engine none the less. Heat in the attic carries the energy that powers the roof vent turbine to spin, causing it to suck air out of the attic, thereby ventilating it.

Turbine Speed Indicators

A turbine speed sensor is but one of the many types of sensors that would be found on a complex turbine engine. Why is it necessary to know the speed that a turbine in an engine is spinning? If the engine is a jet engine, the the turbine is the main power source and the speed that it is rotating would be a prime indicator propulsion.

Turbo Charged Air Intake Systems

Also, a turbine can be an integral part but not the main component of a propulsion system or engine. A prime example of this would be a car with a turbo charged intake system. In this case a turbine speed sensor would provide real time information on how the air intake system is functioning at any given time.

Article by Rosa Telipten. Here you will find everything you wanted to learn regarding Turbine Speed Sensor and even Magnetic Speed Sensors

Article Source: _http://EzineArticles.com/?expert=Rosa_Telip_Ten

Read More......

Optoisolators

Optoisolators are circuits designed to isolate one circuit from another using light. Why would you use light instead of implementing some diodes or voltage regulators? Because light is essentially a guaranteed protection. If an overvoltage or overcurrent is applied to the optoisolator, the optoisolator circuit is destroyed and the circuit(s) it was protecting will not be affected.

The most common optoisolators are placed in an integrated circuit for convenience and efficiency. The most popular model is the 4N33, which is housed in an 8-pin DIP package. The 4N33 internally is basically an LED next to a phototransistor. This could be called an optical modem, since it modulates the electric signal into light waves, which are demodulated by the phototransistor as it converts the light into electricity again.

To design a circuit using an optoisolator, you cannot ignore the components inside of it. On the input circuit, you must take the forward voltage of the LED into account, which can be approximated to .7 volts. On the output side, you should take the phototransistor's forward voltage into account and it can be approximated to .2 volts. If you are working with relatively high voltages, you will need a resistor on the input to protect the LED.

Optoisolators are commonly used to protect expensive circuits from voltage and current surges. One example application would be on the output of a microprocessor. Most microprocessors can't output a very high current, but you might want to be able to power a motor with an output pin. To work around this problem, you could connect the output pin to the optoisolator's input and then connect the motor in series with the output and a voltage supply that is high enough to power the motor. This way, the majority of the current is coming from the independent power supply rather than the microprocessor.

Read More......

The Capacitor

Capacitors are among the most commonly used components in electronics. Their construction is fairly simple, two metal plates and a dielectric layer separating them. Capacitors are very similar to batteries since they store electrical charge. However, capacitors must be charged with electricity, unlike batteries which produce their own using chemicals.

The storage rating of a capacitor is based on the Farad unit. A capacitor with a capacitance rating of one Farad is capable of storing one coulomb of charge (6.25 x 10 ^ 18 electrons) at 1 volt. Although that many electrons seems like a lot, it can only power an average incandescent light bulb for about a minute.

The reason capacitors are used is often because of their quick discharge ability. A chemical reaction in a battery takes time, while the capacitor requires no chemical reaction to discharge electricity. This makes the capacitor a lot faster when it comes to discharging. That is why capacitors are used in cameras and lasers to create a bright flash, rather than batteries.

Capacitors are also used to make DC voltage constant. In power supplies, the voltage can vary. With a capacitor included, it makes up for a lack of voltage and absorbs the excessive voltage. This is necessary in sensitive electronic devices that require constant voltage supplies.

Capacitors are also used to block direct current. Since a capacitor connected in series with a power source is essentially a broken circuit, current cannot flow, once the capacitor is charged. However, alternating current can still flow when connected to a capacitor, since the voltage shifts and the capacitor charges and discharges. When capacitors are connected in parallel the total capacitance in the network is the sum of all the capacitance, Ct = C1+C2…+Cn. For example if C1 was 10uF and C2 is 47uF the total capacitance is 57uF.



When capacitors are connected in series the capacitance is given by 1/Ct = 1/C1+1/C2…+1/Cn.



Capacitors are usually connected in series to increase the total voltage that can be connected between them; this is common with Tesla Coil Circuits as finding a capacitor with the exact capacitance and voltage would be almost impossible to find.

Special care must be taken with high voltage capacitors, such as capacitors where mains voltages (110-120v and 220-240) or the capacitors used in microwaves and TV sets and they can store enough charge to kill. Capacitors can store a charge for years after the power supply has been disconnected and the terminals should be shorted to remove the charge, some high voltage capacitors have ‘bleed resistors’ in them to drain the charge when the power is disconnected.

The different types of capacitors are generally named by the dielectric used in them, and have different purposes.

Aluminium electrolytic capacitors consist of one plate that is a chemical electrolyte and a dielectric that is an oxide on one side of the other metal plate. Aluminium electrolytic capacitors store the most charge in the smallest space with respect to other types of capacitors due to the oxide dielectric's amazing properties as an insulator. There are two main types of capacitor structural designs that you will run into when working with electronics. The two types are radial and axial. The radial design has both leads coming out of the same side of the capacitor. The axial design has one lead coming out of the center of each side, creating an axis.

Read More......

Resistors

Resistors are components that just about every electronic device uses. A resistor is a component that resists the flow of current. They do this by either extending the length of wire that the electricity must flow through or forcing the current to pass through a poor conductor, such as carbon.

It can protect components that have a specific current rating

It can change the function of the circuit

It can create a "dummy load" for a circuit in order for testing purposes

It can create by products such as heat that can be utilized for special purposes

The protection is necessary in order to prevent destruction of certain components that have a maximum current that can be passed through them. This is particularly true in components such as LEDs, which can suffer permanent damage and/or destruction if excessive current is passed through them.

The resistance can change the function of certain circuits, such as oscillators. Certain circuits use the level of current as a control for specific functions. For example, the 555 timer IC outputs pulsed electricity, the frequency of which is determined by the current level sent to one of its leads. This is very important.

The "dummy load" is useful when testing circuits in the lab since the actual load can be impractical for testing (such as a very large antenna). The resistor duplicates the resistance of the real load and makes the circuit act as though it is connected as it normally would.

Resistance creates heat losses in electrical circuits, but that is not always a bad thing. Most electrical heaters utilize this by running electricity through resistors with very low resistance, producing a lot of heat.

On a circuit diagram normally a resistor will have a letter after the value, for values less than 1,000, an ‘R’ is used. So 100 ohms will read 100R. From 1,000 ohms a ‘K’ is used and the number is divided by 1,000. So 1,000 ohms is read as 1K, 22,000 as 22K and 100,000 ohms as 100K. Lastly, from 1,000,000 ohms a ‘M’ is used and the number is divided by 1,000,000. So 1,000,000 ohms is 1M of course. Resistors are too small to have these numbers printed on them, instead they have coloured bands, which is explained further down.

Resistor values with a decimal point in circuit diagrams are expressed in 2 ways, say the circuit requires a 1.2k ohm resistor. The diagram might have it as 1.2K or it might appear as 1K2. The ‘K’ is put in place of the decimal point to prevent the value from being misread as 12K ohms. For resistors below 1k ohm an ‘R’ is used in place of the ‘K’. So 5.6 ohm resistor on the diagram would appear as 5.6R or 5R6.



The above is a picture of a 4-band 1/4w carbon film resistor. These are the most commonly used in electronic circuits due to their low cost and versatility. They come in 1/4w, 1/2w and 1w. You can tell the difference in power handling by the physical size of the package. A 1/4w resistor 7mm long by 2mm diameter, a 1/2w is about 9mm long by 3mm diameter and a 1w is 11mm long and 4mm in diameter. They usually have a tolerance of 5%.



These are 5-band metal film resistors, they have a much smaller tolerance than carbon film resistors, these have a tolerance of 1%. These are used where you need an exact value, such as a high quality audio preamplifier.



This is a ceramic wire wound resistor. They usually come with a power rating of 5w and 10w. These are used where a lot of power is going to be dissipated, such as that of a dummy load. They will be used in a high power audio amplifier.



This is wire wound nichrome wire. The purpose of nichrome wire is to produce heat and hence it’s used in electric heaters and stoves. Nichrome wire normally has a resistance of about 13.8 Ohms per metre. This coil came from a 2400w, 240v fan heater, it had 8 lengths just like the one pictured and they were used in series and parallel combinations to achieve low, medium and high power. The wire actually had a faint red glow on full power. Nichrome wire in heaters should be protected so stray hands don’t touch them, because that stray hand will get burnt.

Because carbon resistors are so small it’s impractical to print the resistance on it so instead they have 4 or 5 coloured bands. The number of bands relates to the tolerance of the resistor, the tolerance is how much variation there is likely to be. At 5% a 100 ohm resistor can be as low as 95 ohms or as high as 105 ohms. 4 bands are used when the tolerance is 5% or 10% and 5 bands are used when the tolerance is 1% or 2%. The 5th band is used to achieve more precision.



The 1st, 2nd (3rd) and multiplier bands are bunched together so you can see where to start from. This is helpful especially with 5-band resistors, which is harder to tell because the tolerance band is brown or red.

Read More......

Transistors

Transistors are electronic switching devices, which are the basis of nearly all electronic circuits. This page will give a brief outline of what they are, as well as different methods to interface analog transistors from digital circuitry.

Introduction

The simple explanation of a transistor is that it is a combination of three 'doped' pieces of semi-conductor material. The piece in the middle is called the Base (in Bipolar Junction Transistors), and the outside edges are the Collector, and the Emitter.

When current is put into the Base, it changes the voltage characteristics of the entire transistor, and so it is possible to control the current flowing from the Collector to the Emitter. So a small change of current on the base, results in a large change between the Collector and Emitter.

Bi-Polar Junction Transistors (BJT)
NPN

This is the simplest type of BJT to understand. As you can see in the diagram below, when you apply voltage to the base of the BJT, it turns on the transistor.

A more detailed explanation is that when current is applied onto the base, it changes the voltage difference between the collector and the base. This difference changes the bias within the transistor, causing current to flow from the collector to the emitter.

When there isn't a lot of charge on the base, there are areas within the semiconductor that aren't capable of carrying current from collector to emitter. This means that a lot of power is dissipated to drive the current through. When there is so much charge on the base that no more will fit, the transistor is said to be saturated. There are plenty of carriers for the current, and not much power is dissipated, making the transistor more efficient. This is only true when the transistors Emitter is connected directly to ground (Common Emitter).

This diagram shows how an NPN is turned on. When the base is turned off (connected to ground), there is no way to put current through the transistor, so the transistor is off. When the base voltage is raised, driving charge onto the base, it turns the transistor on.

PNP

The PNP isn't quite as simple. The base still controls the flow of current, but it is more or less opposite. In order to turn the transistor on the base is connected to ground (turned off). To turn the transistor off, voltage is applied to the base.

The reason for this is because of the type of semi-conductor used. When the base is connected to ground, loose electrons are taken away, creating 'holes'. These holes can be thought of as positive charges, and are capable of carrying current from the Emitter to the Collector.

A PNP transistor will saturate only when it is set up as a Common Emitter

The diagram below shows how this works.

This diagram shows how an NPN is turned on. When the base is turned off (connected to ground), there is no way to put current through the transistor, so the transistor is off. When the base voltage is raised, driving charge onto the base, it turns the transistor on.

Read More......

Inductor

An inductor is a coil of wire which may have a core of air, iron or other ferrous materials. Its electrical property is called inductance and the unit for this is the henry, symbol H. 1 Henry is very large so mH and µH are often used, 1000µH = 1mH and 1000mH = 1H. Iron and ferrite cores increase the inductance since they can become magnetized. Inductors are mainly used in tuned circuits and to block high frequency AC signals (they are sometimes called chokes).

They pass DC easily, but block AC signals, exactly the opposite of capacitors.

Inductance is a property that is possessed by all coils of wire containing electrical current. The current creates a magnetic field, which can in turn induce current flow if the original current decreases in magnitude or stops. Essentially, an inductor is like a capacitor, only stores energy in a magnetic field instead of an electric field. This makes it very useful for power supply filters that help maintain a fairly noiseless current. A transformer is essentially two inductors, where current flow through one inductor induces current flow in the second as a result of the magnetic field.

Inductors are most often found in audio electronics, power supplies, and radio tuning circuits. An inductor can easily be made by winding insulated wire around a ferrous rod. Thin gauge wire is easiest, since it can bend into smaller loops and is cheaper than large gauge wire.

Read More......